PDA

View Full Version : how to install MBC



GokuSSJ4
11-19-2004, 03:01 PM
Proper MBC Install
written by: kpt4321
Currently Offline DSMtuners Wiseman
Location: Massachusetts
Car: 93 Talon TSi AWD

This is a quick overview of the correct way to install a manual boost controller on your turbo DSM.

First, the stock boost control system: There is a pressure source on the turbo outlet elbow (1g) or the compressor housing (2g). That pressure source goes towards the wastegate actuator, but first it has a tee in it. That T splits the source between the WGA and the BCS (boost control solenoid).

The WGA works by opening the wastegate up when it recieves a pressure signal. In order for the car (stock) to increase the boost, it uses the BCS to bleed some of the pressure in the source line off. thus decreasing the pressure that the WGA sees.

When you install a manual boost controller, you are simply replacing this system with a preloaded, pressure-activated valve. That way, the WGA won't see any pressure, until the boost goes about the preload set into the MBC.

First, remove the stock system. Unplug the BCS (or leave it plugged in and toss it aside), remove all the hoses, and cap off both the original source and the fitting before the turbo that the BCS went back to. You won't be needing any of these.

Now, install the new MBC. First, you need to pick a source. Your source has to be a decently sized pressure port AFTER the throttle body. That means that you can not use the throttle body ports (too small) and you can't use anything on the intercooler pipes. Most people tee into the BOV line, and some run a seperate source from the PCV nipple, or their own extra nipple.

You HAVE to use the intake manifold is you want proper boost control. Why is that? The manual boost controller regulates the amount the wastegate is open based on the pressure at its source. Since you want to control manifold pressure, you want the MBC and the WGA to be recieving pressure directly from there.

Using a source off the turbo or intercooler pipe can cause you to have boost that changes with weather, load, and engine speed, and can also slow down boost response. By comparison, a manifold source will be fairly steady, solid, and reliable.

Then connect the source line to the "in" side of the MBC. On most boost controllers, this is the bottom; it will always be the side opposite the adjustment screw (for ball-and-spring MBC's, which are the only kind worth running).

Then, connect the "out" port on the MBC to the wastegate actuator.

Try to minimize the length of all the hoses, and make sure to zip tie them securely such that there are no leaks. Use hose that fits over the fittings well, don't go too big or too small.

All MBC's will have some kind of vent hole after the spring; most new ones have this drilled into the body of the MBC, but some older ones have a seperate piece which goes in the out line. Make sure this is intact and uncovered.

Mount the MBC securely, and go for a test drive! Start with the boost tuned all the way down (generally counter-clockwise) and slowly bring it up to where you want.


Boost Controller Basics

Author: Dan Hurwitz
Page: 1 Last Updated: August 19, 2003

--------------------------------------------------------------------------------

A boost controller is a valve – either passive or active – that regulates the flow of pressure to the wastegate actuator of a turbocharger.A turbo charger is a natural feedback device.Exhaust gas drives the turbo, which makes more boost, which causes the engine to make more exhaust gas, which make more boost…and so on.Without some kind of moderating influence, the turbo would quickly blow up the engine.

The boost controller sits in the vacuum circuit that goes to the wastegate actuator.The wastegate is a bypass for the turbine (hot) side of the turbo.Allowing exhaust gas to flow out the wastegate prevents the turbo from spinning too fast.The wastegate actuator is a pressure-operated diaphragm that moves the flapper door of the wastegate; as boost pressure increases, that pressure also builds against the wastegate actuator.When the pressure gets to a certain level, the wastegate door opens, and pressure will equalize at the desired maximum.

http://features.evolutionm.net/img/articles/machvcorner/boost_controller/boost_controller_diagram.gif
http://forums.evolutionm.net/attachment.php?attachmentid=52117

Most modern cars, including the Lancer Evolution, have a built-in boost control solenoid of some sort.This solenoid allows the engine control unit (ECU) to adjust boost pressure during regular use, or to drastically reduce it in the case of a perceived emergency.(If you filled the car with super-low-octane gas, the ECU might reduce the boost to a minimum, for example.)

An aftermarket boost controller allows independent control of the amount of pressure that reaches the intake manifold, and increased boost (to a point) is great for making more power!Normally, the aftermarket boost control device will take the place of the factory boost control solenoid.This does remove those built in safety features, but it also unlocks the potential for big increases in horsepower

the rest can be found :

http://images.google.com/imgres?imgurl=http://features.evolutionm.net/img/articles/machvcorner/boost_controller/boost_controller_diagram.gif&imgrefurl=http://features.evolutionm.net/article/machvcorner/30&h=371&w=585&sz=14&tbnid=x_pPVxBHiPEJ:&tbnh=83&tbnw=130&start=44&prev=/images%3Fq%3Dboost%2Bcontroller%26start%3D40%26hl% 3Den%26lr%3D%26sa%3DN