View Full Version : EVO MR 6spd - 4th gear size
KareBearPowa
09-10-2006, 01:50 PM
I got my rebuilt 6spd back from TRE and installed finally and Jon@TRE sent me back my broken 4th gear as I requested. I measured it so everyone can see just how small this gear is. Honestly, I have a new found appreciation for gears, I have no idea how something like this can hold the power these cars can put out.
http://www.norcalmotorsports.org/users/bryan/mods/EVO/broken_6spd/evoMR_6spd_4thgear_size01.jpg
http://www.norcalmotorsports.org/users/bryan/mods/EVO/broken_6spd/evoMR_6spd_4thgear_size02.jpg
http://www.norcalmotorsports.org/users/bryan/mods/EVO/broken_6spd/evoMR_6spd_4thgear_size03.jpg
http://www.norcalmotorsports.org/users/bryan/mods/EVO/broken_6spd/evoMR_6spd_4thgear_size04.jpg
For the back-story on how I broke 4th see the whole thread here: http://forums.evolutionm.net/showthread.php?t=210221
got any pics and measurement of the new tre gears?
KareBearPowa
09-10-2006, 04:21 PM
got any pics and measurement of the new tre gears?
Same stuff. AFAIK there are no "upgraded" gears avail.
crctslt
09-10-2006, 06:58 PM
Looky what I found
http://www.magnusmotorsports.com/images/evogearset.jpg
KareBearPowa
09-10-2006, 07:30 PM
Looky what I found
http://www.magnusmotorsports.com/images/evogearset.jpg
Dog gears for the 5? Seen that before, did you see the gear cost? $4800!
crctslt
09-10-2006, 08:53 PM
Yeah I saw :P Gear noise FTMFW!
Bet you won't break them though.
KareBearPowa
09-10-2006, 09:01 PM
Yes but I would also need a 5spd to put them in. ;)
vtluu
09-10-2006, 09:28 PM
I have no idea how something like this can hold the power these cars can put out.
It can't, apparently. :nana:
http://www.magnusmotorsports.com/images/evogearset.jpg
Dog gears for the 5? Seen that before, did you see the gear cost? $4800!
O.o time for me to start putting aside some gear fund then =/
crctslt
09-10-2006, 10:50 PM
Yes but I would also need a 5spd to put them in. ;)
What you're going to let a little thing like not owning a 5 get in the way?
KareBearPowa
09-11-2006, 09:24 AM
TRE updated their website to show everything they do when they rebuild a gearbox:
Stage 1
The parts replaced:
New 1-5th & Reverse synchros
New 1st-2nd hub & sleeve
New 3rd/4th hub & sleeve
New 5th/Reverse hub & sleeve
New 3rd/4th shift fork
New 5th/Reverse shift fork
New Input shaft bearings
New output shaft bearings
New needle bearings
New oil seals
New synchro springs
New heavy duty Neodymium trash magnet & magnetic drain plug. Keeps the oil clean.
New snap rings, roll pins, end nuts, bearing shims and all the other non-reusables that you would expect to be replaced in a quality rebuild.
Stage 2
Everything in stage 1 plus:
INCLUDING:
Glass beading of transmission case. Your transmission will look like new.
Enlarged oil passages. This makes for a cooler running, better shifting, long lasting transmission.
Shift assembly, shift rails, hub & sleeves are vibratory deburred & and REM ISF® finished for the best shift quality.
Gears, shafts, shift assembly, shift rails, hub & sleeves receive detail work
Stage 3
Everythign in stage 1 and 2 plus:
INCLUDING STAGE 2:
Glass beading of transmission case. Your transmission will look like new.
Enlarged oil passages. This makes for a cooler running, better shifting, long lasting transmission.
Shift assembly, shift rails, hub & sleeves are vibratory deburred and REM ISF® finished for the best shift quality.
INCLUDING STAGE 3:
Gears & gearshafts shot peened. Substantial fatigue resistance and gear wear reduction have been achieved.
06IXMR
09-11-2006, 10:58 AM
How much did that run you with all the shipping and everything?
vtluu
09-11-2006, 11:06 AM
http://www.teamrip.com/transship.html
Round-trip shipping is $175.
Stage 3 is looking pretty darned good to me... :drool:
KareBearPowa
09-11-2006, 11:07 AM
Stage 2 is $1450 plus I payed about $150 each or so for the new 4th gear input and output gears. Shipping is a flat $175 round trip with box included (he sends a very sturdy box out, you pack it with your tranny and send it to him, they send it back after its done).
I think my bill was approx $1750
Powered by vBulletin® Version 4.2.4 Copyright © 2024 vBulletin Solutions, Inc. All rights reserved.